Lexmark C 760 Instrukcja Użytkownika

Setup GuideJune 2004www.lexmark.comLexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United St

10 Set up the printer and paper handling optionsNote: Leave the printer in the box until you are ready to install it, then have someone help you lift

11 Set up the printer and paper handling optionsPrinter setup If you only purchased a base printer with no options, follow the directions under “Posit

12 Set up the printer and paper handling optionsInstalling a 500-sheet drawerYour printer supports up to three additional 500-sheet drawers. However,

13 Set up the printer and paper handling optionsInstalling a duplex unit Your printer supports an optional duplex unit that lets you print on both sid

14 Set up the printer and paper handling options2 Have someone help you place the printer in the location you have chosen.If you are installing the pr

15 Set up the printer and paper handling options5 Attach the printer top cover to the output expander.6 Attach the output expander paper bail to the t

16 Set up the print supplies5 Attach the printer top cover to the mailbox.6 Attach the mailbox paper bail to the top cover.Step 5: Set up the print su

17 Set up the print supplies3 Remove the print cartridges. For each cartridge:a Pull up on the handhold.b Pull the cartridge straight out and use the

18 Set up the print suppliesWarning: Failure to remove the packing material from the print cartridges damages the printer.c Turn the cartridge so the

19 Install memory, firmware, or option cardsAttaching an operator panel overlayIf English is not your preferred language and your printer shipped with

20 Install memory, firmware, or option cardsRemoving the system board access cover1 Locate the access cover on the back of the printer.2 Remove the fo

21 Install memory, firmware, or option cardsInstalling a memory card Follow the instructions in this section to install a printer memory card. Memory

22 Install memory, firmware, or option cardsInstalling a firmware card Follow the instructions in this section to install an optional firmware or flas

23 Install memory, firmware, or option cardsInstalling a hard disk Follow the instructions in this section to install an optional hard disk. You need

24 Install memory, firmware, or option cardsInstalling an option card Your printer has one expansion card slot that supports a number of option cards.

25 Install memory, firmware, or option cardsReplacing the system board access coverAfter you have finished installing cards on the printer system boar

26 Load paperStep 7: Load paperNote: When loading specialty media such as transparencies or card stock, refer to the User’s Guide on the publications

27 Load paper5 Place the paper against the back left corner of the tray, print side down.Do not load bent or wrinkled paper.Note: Do not exceed the ma

28 Load paper3 Squeeze the two front guide levers and slide the guide to the correct position for the size paper you are loading.4 Slide the bottom su

29 Load paperLoading the multipurpose feederYou can use the multipurpose feeder one of two ways:• Paper tray—As a paper tray, you can load paper in th

English

30 Attach cables and power cordStep 8: Attach cables and power cordCAUTION: Do not connect or disconnect a communication port, a teleport, or any othe

31 Verify printer setup2 Plug one end of the printer power cord into the socket at the back of the printer and the other end into a properly grounded

32 Verify printer setup4 Verify the options you installed are correctly listed under “Installed Features.”If an option you installed is not listed, tu

33 Configure for TCP/IPStep 10: Configure for TCP/IPIf you have TCP/IP available on your network, we recommend that you assign an IP address to the pr

34 Configure for TCP/IPStep 11: Install drivers for network printingAfter you have assigned and verified the TCP/IP settings, you are ready to install

35 Configure for TCP/IPDirect printing using Windows 98 SE, Windows Me, Windows NT 4.0, Windows 2000, Windows XP, and Windows Server 2003To install a

36 Configure for TCP/IPe In the Alternate Drivers section, select the operating systems of all the network clients that will print to the printer.f Cl

37 Configure for TCP/IPMac OS X version 10.1.2 and laterStep 1: Install a custom PPD file 1 Insert the drivers CD.2 Double-click the installer package

38 Other sources of information• If the PPD file displayed in the Summary window is correct for your printer, then printer setup is complete.• If the

39 Other sources of informationTo print these pages:1 On the operator panel, press Menu until you see Help Menu, and then press Select.2 Press Menu un

Edition: June 2004The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL,

5 ContentsContentsStep 1: Choose your setup (local or network printer) . . . . . . . . . . . . . . . . . . . . . . . . 7Local printer . . . . . . . .

6 ContentsStep 12: Other sources of information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Viewing and using the public

7 Choose your setup (local or network printer)Step 1: Choose your setup (local or network printer)Local printer A local printer is a printer attached

8 Install drivers for local printingNote: Some Windows operating systems require that you have administrative access to install printer drivers on you

9 Unpack the printerUNIX/Linux Local printing is supported on many UNIX and Linux platforms, such as Sun Solaris and Red Hat.The Sun Solaris and Linux